SPE Stone & Marble Sealer Ready-To-Use
Nano-Technology Water-Repellent Impregnation for Mineral Surfaces
SPE Stone & Marble Sealer is a high-performance, waterborne impregnating sealer formulated with modified silanes and polysiloxanes on the nano scale. The product penetrates deeply into porous mineral substrates to create a durable hydrophobic barrier while maintaining the natural breathability of the surface.
Once applied, SPE Stone & Marble Sealer significantly reduces water absorption while allowing water vapour to escape, helping protect substrates against moisture ingress, staining, and salt efflorescence.
SPE Stone & Marble Sealer RTU 5L
Waterborne emulsion of modified silanes and polysiloxanes engineered at the nano scale for impregnation of stone, marble, and other absorbent cementitious substrates.
- Excellent water-repellent performance
- Highly penetrating impregnation system
- Strong surface water-beading effect
- Breathable – does not block water vapour permeability
- High early water resistance
- Reduces surface soiling
- Helps prevent soluble salt efflorescence
- Maintains natural appearance of the substrate
SPE Stone & Marble Sealer is suitable for use on a wide range of absorbent mineral substrates including:
- Natural stone
- Marble
- Brick and clinker brick
- Sandstone
- Mineral plaster
- Cement-based surfaces
The product can be used as a water-repellent impregnation treatment or as a base coat for mineral surfaces requiring moisture protection.
Property Typical Value
Appearance Milky white liquid
Active Ingredient ± 50%
Specific Gravity (20 °C) ± 0.95 g/cm³
Application
Ensure surfaces are clean, dry, and free of dust, oil, grease, or loose material before application.
Apply SPE Stone & Marble Sealer generously to the absorbent surface using:- Brush
- Roller
- Low-pressure spray
- Flooding method
For optimal coverage and to avoid missed areas, two applications applied wet-on-wet are recommended.
Allow the product to penetrate fully into the substrate.
SPE Stone & Marble Sealer is sensitive to extreme temperatures.
- Do not store below 0 °C
- Do not store above 40 °C
Exposure to frost or excessive heat may cause irreversible damage to the product.
During prolonged storage, the product may show slight creaming, sedimentation, or separation. This is normal. Stir thoroughly before use.
Available in 5 L and 25 L containers.
The coverage rate of SPE Stone & Marble Sealer depends largely on the porosity and absorption capacity of the substrate.
To determine the approximate product requirement, it is recommended to conduct a simple water absorption test on the surface prior to application. The amount of water absorbed by the substrate provides a practical indication of the quantity of SPE Stone & Marble Sealer required to achieve effective impregnation.
Highly porous surfaces will require higher product consumption, while dense substrates will require less material.
Always perform a small test application to determine the correct coverage rate and to confirm suitability for the specific substrate.The manufacturer warrants that the product conforms to its published specifications at the time of manufacture. This warranty is limited to a period specified for the individual product, calculated from the date of purchase, and is conditional upon correct storage, surface preparation, application, and maintenance in accordance with the manufacturer’s published guidelines.
Larik Solutions Pty Ltd acts solely as the supplier of this product and provides no additional warranty, express or implied. No warranty of merchantability or fitness for a particular purpose is given.
As application methods, substrate conditions, environmental factors, workmanship, and methods of use are beyond the control of both the manufacturer and Larik Solutions Pty Ltd, no responsibility can be accepted for results obtained or for any loss or damage, whether direct, indirect, incidental, or consequential, arising from the use or misuse of the product.
All performance data, coverage rates, and recommendations are provided in good faith and are based on internal testing and practical experience. Actual performance may vary depending on substrate type, surface preparation, application thickness, environmental exposure, and site conditions. Users must conduct their own tests to determine suitability for the intended purpose before full application.
By purchasing, using, or applying this product, the user acknowledges and agrees that:
-
The product is supplied as a protective coating or additive, and not as a certified or guaranteed system unless expressly stated otherwise in writing.
-
Any technical guidance, recommendations, or application advice provided by the manufacturer or Larik Solutions Pty Ltd is offered in good faith but does not constitute a guarantee of performance or outcome.
-
The user assumes full responsibility for verifying that the product is suitable for their specific application, substrate, and service conditions.
-
Neither the manufacturer nor Larik Solutions Pty Ltd shall be held liable for any direct, indirect, incidental, or consequential loss or damage, including but not limited to property damage, loss of use, equipment failure, or injury, arising from the use, misuse, or incorrect application of the product.
-
All risk associated with the use of the product rests entirely with the user, and use of the product constitutes acceptance of this indemnity in full.
-
