SPE Stone and Marble Sealer Concentrate 5L

Get more for your money with our high-performance concentrate, available in two convenient sizes.

• 25 Liters Concentrate - makes up to 250 Liters ready-to-use solution

With a consistent 1:10 dilution ratio, our product delivers maximum , efficiency you're tackling small tasks or large-scale jobs. Save on storage, reduce  waste, and packaging unlock unbeatable value with every liter.

 

SPE Stone & Marble Sealer Concentrate is suitable for use on a wide range of absorbent mineral substrates including:

• Natural stone
• Marble
• Brick and clinker brick
• Sandstone
• Mineral plaster
• Cement-based surfaces

Always apply ready-to-use solution
The product can be used as a water-repellent impregnation treatment or as a base coat for mineral surfaces requiring moisture protection.

Application
Ensure surfaces are clean, dry, and free of dust, oil, grease, or loose material before application.
Dilute 1:10 before applying - always apply ready-to-use solution.

Ensure surfaces are clean, dry, and free of dust, oil, grease, or loose material before application.

Dilute 1:10 before applying - always apply ready-to-use solution.

Apply SPE Stone & Marble Sealer Ready-To-Use generously to the absorbent surface using:

• Brush
• Roller
• Low-pressure spray
• Flooding method

For optimal coverage and to avoid missed areas, two applications applied wet-on-wet are recommended.
Allow the product to penetrate fully into the substrate.

• 5 litres makes up to 50 litres
• 25 litres makes up to 250 litres

• Appearance: Milky white liquid
• Active Ingredient: ± 50%
• Specific Gravity (20 °C): ± 0.95 g/cm³

• Available in 5 L and 25 L containers

SPE Stone Sealer Concentrate is sensitive to extreme temperatures and must be stored between 0°C and 40°C. Exposure to frost or excessive heat may cause irreparable damage. If the product is suspected to have been exposed to such conditions, its usability must be verified before use.

The manufacturer warrants that the product conforms to its published specifications at the time of manufacture. This warranty is limited to a period specified for the individual product, calculated from the date of purchase, and is conditional upon correct storage, surface preparation, application, and maintenance in accordance with the manufacturer’s published guidelines.

Larik Solutions Pty Ltd acts solely as the supplier of this product and provides no additional warranty, express or implied. No warranty of merchantability or fitness for a particular purpose is given.

As application methods, substrate conditions, environmental factors, workmanship, and methods of use are beyond the control of both the manufacturer and Larik Solutions Pty Ltd, no responsibility can be accepted for results obtained or for any loss or damage, whether direct, indirect, incidental, or consequential, arising from the use or misuse of the product.

All performance data, coverage rates, and recommendations are provided in good faith and are based on internal testing and practical experience. Actual performance may vary depending on substrate type, surface preparation, application thickness, environmental exposure, and site conditions. Users must conduct their own tests to determine suitability for the intended purpose before full application.

By purchasing, using, or applying this product, the user acknowledges and agrees that:

• The product is supplied as a protective coating or additive, and not as a certified or guaranteed system unless expressly stated otherwise in writing.

• Any technical guidance, recommendations, or application advice provided by the manufacturer or Larik Solutions Pty Ltd is offered in good faith but does not constitute a guarantee of performance or outcome.

• The user assumes full responsibility for verifying that the product is suitable for their specific application, substrate, and service conditions.

• Neither the manufacturer nor Larik Solutions Pty Ltd shall be held liable for any direct, indirect, incidental, or consequential loss or damage, including but not limited to property damage, loss of use, equipment failure, or injury, arising from the use, misuse, or incorrect application of the product.

• All risk associated with the use of the product rests entirely with the user, and use of the product constitutes acceptance of this indemnity in full.